What is edge molding

Cabinet edge molding refers to any molding that adorns a cabinet edge, such as crown, light rail and shelf molding. Typically, it’s made of wood, plaster or some other engineered material.

What is the trim on top of cabinets called?

Crown molding is decorative trim that is added to the top of your cabinets. The benefit of installing crown molding is that it draws the eye upward, showcasing the elegance of your cabinets. Crown molding can either bond with the ceiling or allow for space above the cabinet.

What is Batten Moulding?

Batten trim or batten molding is a thin strip of trim typically with a rectangular cross-section, used to cover seams between panels of exterior siding or interior paneling.

What is starter molding?

A Starter or Riser Molding is mounted to the cabinet top in order to simulate an extension of the cabinet box, allowing the Crown Molding to be installed higher.

What is scribe Moulding used for?

Scribe molding is a strip of wood molding for the side or top the cabinet against an uneven wall or ceiling that provides a finished look sans any gaps. The most common use is for cabinets that are mounted against brick, cinderblock, or stone walls.

What is outside corner molding?

Outside corner molding defines a style of molding that will be used to cover a raw corner of the cabinet box. When installing cabinetry, the edges of the cabinet boxes are typically left raw and unfinished to allow for the addition of decorative edges later in the installation process.

What is the difference between molding and trim?

This is a common question, and the answer is pretty simple. TRIM is a general term that refers to all molding in a home (i.e. window casing, door casing, baseboards, etc.). MOLDING (or moulding) is a broad classification of millwork (any type of woodwork that is produced in a mill …

What is crown molding in kitchen?

Crown molding is simply the decorative piece that covers the top of your kitchen cabinets. They are typically used to finish and complete the aesthetic look in the kitchen.

What is the bottom of a kitchen cabinet called?

Sometimes called floor or lower cabinets, base cabinets are the lower section of cabinetry that is installed on the floor. Makes sense, right? They are almost always capped off with a countertop of some sort, and are usually 24” deep and 36” high in American kitchens.

What is wall moulding?

By definition, a molding is simply a strip of wood (or, occasionally, of plaster or other material) that is used for finish or decorative purposes. … In addition to the cornice and baseboard, the terms picture rail and chair rail refer to where certain moldings are located on a wall.

Article first time published on

What is wall trim?

Wall trim is designed to hide joints, gaps, and other imperfections on surfaces, but most people add trim to their rooms because it is a bold design statement. White trim is a striking accent against a field of dark-colored walls, imbuing these rooms with a formal, traditional look.

What is wall moulding called?

Baseboard: Also called wall base, this moulding is applied around the lower perimeter of the room along a finished floor.

What is a toe kick?

A toe kick is the recessed space on a lower cabinet that offers room for – you guessed it – your toes. These few inches enable your feet to rest comfortably under a small section of the cabinet, allowing you to get closer to the countertop without having to hunch over.

What are shoe moldings?

Paired with a baseboard and painted to match, shoe moulding (also called “base shoe”) is a thin strip of moulding that finishes out the look of baseboards. It can often be found in a curved or round shape similar to quarter round moulding.

What is scribe wood?

A method of marking wood that transfers a profile directly is called scribing. … Marking the exact angle to join two pieces of wood is another application. Scribing tools have sharp metal points which scratch the wood to mark it for cutting.

Are baseboards and trim the same?

Baseboard is the wood (or other material) board that runs between the floor and the wall. … Trim is a broad term that encompasses baseboard and other trim throughout the home.

Can you mix trim styles in a house?

Trim types can be mixed and matched, but as with any design concept, there is an art to achieving an appealing aesthetic.

What is ranch casing?

Casings are used to frame interior and exterior windows and doors. Casings are great for covering up uneven joints where walls meet doors and windows. Available in a variety of sizes, shapes and finishes, casings can create an opening frame that draws attention and brings out the beauty of any door or window.

Should cabinet crown molding touch the ceiling?

1 ) Never leave crown moldings closer than 9 inches from a ceiling. Once you get within a foot of the ceiling you should have the cabinetry and molding meet the ceiling. Don’t create spaces that look odd and that can’t be cleaned. Molding too close to ceiling without reaching it.

What are stiles on cabinets?

Stile – The vertical-framing members of a cabinet face frame or cabinet door.

What is the top of the kitchen called?

A countertop, also counter top, counter, benchtop, worktop (British English) or kitchen bench (Australian or New Zealand English), is the firm, flat, horizontal surface of a counter. They are built for work in kitchens or other food preparation areas, bathrooms or lavatories, and workrooms in general.

What are cabinet door stiles and rails?

Stiles and rails are terms commonly shared between builders, cabinetmakers, designers and homeowners. The definition is simple: stiles run vertically, while rails run horizontally. The two terms refer to the cabinet face frame and the doors, if the doors have a center panel.

Is crown molding outdated?

Crown molding has been around for centuries and it will continue to be a touch of elegance for centuries to come. It is not going out of style. However some people have a preference for it while others will never notice it until it’s not there.

Do modern kitchens have crown molding?

To achieve this clean, spacious look, contemporary cabinets will not have any crown molding or raised panels. … Materials used in contemporary kitchen cabinets are usually man-made such as metal, concrete, plastic or glass.

What height should cabinets be for crown molding?

By far the most complex of the three general types of moldings, crown moldings are optionally mounted on the tops of the wall cabinets and are most often a total height of between 2″ and 6″. The taller crown moldings (e.g. 6″ height) are custom designed with multiple pieces and are installed to suit your kitchen.

What are the different types of trim molding?

of 15. Crown Molding. Given its name, it’s no surprise that crown molding is the king (or queen!) of trim. …
of 15. Baseboard. …
of 15. Chair Rail. …
of 15. Picture Rail. …
of 15. Picture Frame Molding. …
of 15. Panel Molding. …
of 15. Door or Window Trim (Casing) …
of 15. Pierced Molding.

How many types of molding are there?

These 5 types are extrusion moulding, compression moulding, blow moulding, injection moulding and rotational moulding.

What is the trim between wall and ceiling?

Crown. This molding is the “crowning” architectural feature of a room, as it decorates the transition between walls and the ceiling. Crown moldings, also known as cornice moldings, typically boast intricate silhouettes—although many types of crown molding exist.

What are the four types of moldings?

Wall and ceiling: Chair rail, panel moulding, wainscoting, picture rail and crown moulding.
Floor: Baseboard moulding.
Doors and windows: Casing or architraves.

What is half wall molding called?

Wainscoting (pronounced “waynes-coating” or “wayne-scotting”) is wooden paneling that lines the lower part of walls along the perimeter of a room.

What is door molding?

Quite simply, it’s a moulding profile which frames (or trims) a door or window. Casing is functional as well as decorative. The main purpose of casing is to surround all doors and windows, covering any space or gap left between the drywall and frame.