What is a tension tie

Tension ties offer a solution for resisting tension loads that are fastened with nails. The HTT4 and HTT5 are the latest generation of tension ties. They feature an optimized nailing pattern which results in better performance with less deflection.

What are tension ties used for?

Tension ties offer a solution for resisting tension loads that are fastened with nails. The HTT4 and HTT5 are the latest generation of tension ties. They feature an optimized nailing pattern which results in better performance with less deflection.

What is HDU in construction?

HDU holdowns are pre-deflected during the manufacturing process, virtually eliminating deflection under load due to material stretch. They use Simpson Strong-Tie® Strong-Drive® SDS Heavy-Duty Connector screws which install easily, reduce fastener slip and provide a greater net section when compared to bolts.

Are deck tension ties required?

The International Residential Code (IRC) requires that decks be designed to withstand both vertical and lateral loads. This 2015 code allows for tension ties to be attached to the deck joist then fastened directly to an interior sill plate, wall plate or stud – all from the outside.

What is a Simpson Strong wall?

The Strong-Wall wood shearwall is a field-adjustable, prefabricated, engineered wood panel that helps structures resist lateral forces such as those created by earthquakes and high winds. Strong-Wall® Wood Shearwall Multi-Story Kit.

How many deck tensioners do I need?

2.2. 3) states that “hold-down tension devices” be installed in at least two locations per deck. Whether you are attaching a deck that’s 3 ft. long or 30 ft.

How do I make my deck not sway?

How to Brace a Swaying Deck. All decks using horizontal decking should have a diagonal sway brace to prevent racking. You may install a metal “T” brace, which is a long metal strip diagonally across the top of the joists, or install a diagonal deck board across the bottom of the deck frame.

How do you attach 4x4 posts to a deck?

The quickest and most secure way to mount a wooden 4×4 or 6×6 deck post to an existing deck surface is via a Titan Post Anchor. Titan Anchors provide a solid, powder-coated steel connection point for your wooden post to attach to surface below.

Is a joist hanger stronger than nailing?

Joist hangers are better because they allow for more accurate placement of joists. They also allow for toe-nailing, plus support the underside of the joist. This makes the hanger stronger than a toe-nail. While joist hangers are an expense, the ease and increased strength make them a better choice.

Can you join two joists together?

Sistering or Joining Joists Sistering joists is commonly used when adding onto an existing deck or repairing a deck. In these cases, the overlapped joists help tie the framing together by combining the rigid members over a beam. The longer the overlap distance, the stronger the connection.

Article first time published on

What is a steel strong wall?

The Steel Strong-Wall shearwall is a prefabricated, steel panel that helps structures resist lateral forces such as those created by earthquakes and high winds. … This code-listed shearwall is suitable for residential construction.

How much does a Simpson Strong wall cost?

Simpson Strong-Tie WSW24X10-117 24X117.25 Wood Strong Wall w/Front Access HoldownsSimpson Strong-Tie WSW12X9-105 12X105.25 Wood Strong Wall w/Front Access HoldownsOur Price: $401.47 AddOur Price: $720.66 Add

What is a shear wall in a building?

shear wall, In building construction, a rigid vertical diaphragm capable of transferring lateral forces from exterior walls, floors, and roofs to the ground foundation in a direction parallel to their planes.

What is a deck tie back?

The DTB-TZ Deck Tie Back provides positive anchorage between the deck framing and the exterior wall with a load carrying capacity that exceeds building code requirements.

Are decks supposed to shake?

If your deck gets a case of the shakes when you walk across it, there’s probably no reason for concern. Still, in some cases, the deck movement puts extra stress on the fasteners and connectors.

What causes a deck to sway?

When people exit your house and walk onto your deck, it creates a parallel movement, causing that noticeable, sideways sway. Over time, environmental factors like strong winds can also cause the deck to push against the walls and sway, furthering the risk of collapse.

What is deck blocking?

Deck Blocking And Bridging Probably, the most commonly used technique is to install small pieces of material in a zig-zag pattern between the perimeter joists to create a rigid rim joist that prevents bounce and increases the strength of the rail attachment.

What is a deck hold down device?

These new hold-down devices must be attached to the joists of the deck, penetrate through the ledger board, the wall sheathing and band joist of the house, and then fasten to the floor framing inside the house. … In such a case, the devices should be used to tie the deck joists directly to the house joists.

What is a ledger board?

Definition of ledger board 1 : a horizontal board forming the top rail of a simple fence or the handrail of a balustrade. 2 : a flooring board in scaffolding.

What are horizontal loads?

What is Horizontal Loading? Contrary to vertical loading, horizontal loading is when all the sets of a given exercise are done before moving on to the next exercise. … When the client completes 3 or 4 sets of a single exercise, they move on to the next exercise working a different muscle group.

Do decks need hurricane straps?

Hurricane ties will not usually be required by your local building department, but they are a cost-effective method of securing your joists over a cantilevered beam that may be lifted by high winds.

Can you build a deck without attaching it to the house?

A freestanding deck, simply put, is a deck that isn’t attached to another structure. It can be built right next to a house, almost like it’s attached to it, but it will still be self-supporting.

Should a deck be attached to the house?

Without any solid attachment a house, your deck will sway and wobble. It needs bracing, especially if it is high off the ground.

Can I use screws for joist hangers?

Outdoors use 16d double-dipped galvanized nails (or stainless steel when called for) for installing hangers. … The manufacturers agree: Never use galvanized deck screws or drywall screws to install joist hangers. Those screws don’t have the shank size and toughness to support joist loads.

How much weight will a joist hanger support?

Joist SizeMin Capacity lbs2×64002×85002×106002×12700

Is toe nailing stronger?

TOE-NAILING In contrast, toe-nailing produces a strong joint. The technique requires a pair of nails, driven at opposing 45-degree angles. It isn’t suitable for all joints, as the grain of one workpiece needs to be at an angle to the other.

What can I use instead of joist hangers?

Alternatives to using metal joist hangers are ledger strips, sliding dovetails or mortising and dowels. The methods vary depending on whether it is an exterior deck or an interior platform. When it comes to outdoor decks, the only plausible do-it-yourself technique would be to use a ledger strip to support the joists.