Does ardex make Henry

HENRY, a division of ARDEX Americas, is a manufacturer of adhesives for all types of flooring installations.

What color is Henry feather finish?

Manufacturer‎ArdexSize‎7 lbColor‎GrayMaterial‎WoodPower Source‎Air Powered

Can ardex feather finish be sanded?

The final coat when dry should be sanded as smooth as possible before putting on color or sealant. I would allow 1 day between coats. Ardex Feather Finish dries really fast, but better to give it 24 hours to be sure. … The final coat when dry should be sanded as smooth as possible before putting on color or sealant.

Can you sand Henry feather finish?

We applied two coats of the Feather Finish with ample drying time in between. After it’s completely dry and set (follow package directions), you’ll want to sand out any lines made with your knife. My husband held a Shop Vac in one hand and his palm sander in the other in order to minimize the dust.

How do you use Henry 549?

HENRY 549 FeatherFinishTM can be applied to any prepared surface using a steel trowel. Apply sufficient pressure to fill all defects and to featheredge the product into the subfloor surface. It is not necessary to leave a certain minimum thickness of product on the substrate.

Is feather finish waterproof?

ARDEX FEATHER FINISH – Laminate Floors and Waterproof Flooring-Carpet-Wood-Tile-Parquet-Soundproofing-Vinyl-Porcelain in Miami Florida Talula Floors.

How long does Henry feather finish take to dry?

Allow thorough drying to a clear, thin film (min. 3 hours, max. 24 hours). NON-POROUS SUBSTRATES: ARDEX FEATHER FINISH will bond to some non-porous substrates, such as burnished concrete, terrazzo, and ceramic and quarry tile, without the use of a primer.

Can you concrete over laminate countertops?

From what I’ve read, a concrete skim-coat would transform my laminate without having to remove or rebuild the counters. It’s applied straight on top of the laminate in troweled-on layers. … The product I used is Henry brand Feather Finish concrete Underlayment Patch and Skimcoat. I got mine from Home Depot in a 7lb.

What is feather finish used for?

ARDEX FEATHER FINISH® is an underlayment formulated from a blend of Portland cement and other hydraulic cements that provides a smooth, permanent finish for a variety of substrates prior to the installation of today’s demanding floor coverings, including sheet vinyl and VCT (vinyl composition tile).

How thick can you apply ARDEX FEATHER FINISH?

ARDEX FEATHER FINISH can be easily applied with a steel trowel, and used at a true feather edge, or up to 3mm in thickness. For thicknesses of 3mm, and not exceeding 12mm, it is recommended to build up in thin applications or alternatively consult the ARDEX ARDURAPID A 45 datasheet.

Article first time published on

How thick can ardex be installed?

ARDEX K 521™ is a pourable, polishable, self-leveling topping for fast-track resurfacing of indoor concrete. ARDEX K 521 can be installed from a minimum thickness of 3/8″ (9 mm) up to a maximum thickness of 2″ (5 cm). Use ARDEX K 521 to provide a polished, “aggregate-exposed” surface.

Can ardex be used outside?

ARDEX K 301™ Exterior Self-Leveling Concrete Topping is a self-leveling topping and underlayment for fast-track resurfacing and smoothing for exterior and interior applications over concrete and approved, properly prepared, non-porous surfaces, including terrazzo, epoxy coatings and ceramic and quarry tile – on, above …

What is feather edge concrete?

ProSpec Feather Edge is a trowelable, rapid setting, polymer- modified, cement-based patch and skim coating compound that results in an ultra-smooth, thin finish applied under resilient flooring, VCT and a wide array of floor coverings. Features and Benefits. • Featheredge up to 1/2” (13 mm) thickness without cracking.

How long does VCT adhesive take to get tacky?

Allow adhesive to turn clear and become tacky. When touched with a finger, the adhesive should not transfer to the finger. The amount of time in which the adhesive becomes tacky will vary with temperature and humidity. Adhesive will remain tacky for approximately 8 to 12 hours.

How long does it take for Henry 356 to dry?

Adhesive must set 24-48 hours before exposing to heavy traffic.

Can you install VCT tile on plywood?

You can lay VCT over a variety of flooring materials, including concrete and wood. … To level an even wood floor, place an underlayment layer of plywood over the flooring. Remove door thresholds, base moldings and other trim work so you can easily install the tile.

What consistency should Feather Finish be?

Step 2: Mixing the Feather Finish Concrete Gradually add the feather finish concrete stirring until it is about the consistency of drywall mud or a thick frosting. If it gets too thick you can always add more water. It needs to be spreadable, but not too thin that it will not adhere to the edge of the countertop.

What is feather floor?

Feather finish irregular floors. Designed to smooth grooves, joins, gaps and grout joint lines over concrete, terrazzo and ceramic tiles. … Feather Floor is easily applied to any prepared surface using a steel trowel. Apply sufficient pressure to fill all defects and to feather the product into the subfloor surface.

Does ardex feather finish expire?

The shelf life of ARDEX PC-T and ARDEX SD-T is extended to 9 months (previously 6 months) for unopened, properly stored bags. We are writing to clarify our recommendations for the installation of ARDEX products with consideration to the new OSHA Standard on crystalline silica.

How many square feet does a bag of Ardex Feather Finish cover?

Coverage: 16.7 sq. ft. per bag at 1/4”, 33.3 sq. ft.

Does feather finish concrete?

One thing that’s important to know about the Feather Finish concrete countertops is that it is not as hard as regular concrete. … My Feather Finish concrete is applied in thin layers on top of laminate counters, so there’s a bit of a durable surface underneath the concrete.

Can you put concrete over Formica countertops?

First I sanded the surface of the existing formica countertop with a coarse sandpaper (the cement will hold better to a rough surface). … We also took out the sink so I could get under the lip of where the sink sits on the counter. Use a small disposable container and a paint stirrer to mix your cement.

How do I use ardit feather finish?

INSTALLATION DUNLOP ARDIT FEATHER FINISH is easily applied to the prepared surface using a steel trowel. Apply sufficient pressure to fill all defects and to feather the product into the subfloor surface. Apply sparingly to obtain the desired smoothness and finish for your application.

How do you cover old laminate countertops?

Use paint to cover old laminate and give it a fresh new color. Oil-based paint will adhere as long as the countertops are properly prepared and finished. This includes a through cleaning, sanding and cleaning again, followed by a coat of primer designed to bond with plastic.

How thick can you put on feather finish?

ARDEX FEATHER FINISH is easily applied with a steel trowel and can be used to form a true feather edge up to 3mm in thickness. ARDEX FEATHER FINISH is designed specifically for very thin smoothing applications typically 1mm thick or less, but may be used up to 3mm thick in one application.